4 Important Checks: Plumbing Systems

Plumbing System

When it comes to your plumbing system, it is always better to take precautionary measures than to wind up with a big mess. Do not ignore any signs when it comes to your plumbing. Ignoring the issue could lead to bigger problems and more expenses. Here are 4 things to check when it comes to your plumbing system.

1. Leaky Faucets

Leaky faucets can cause higher water bills and irritation. The constant drip of a leaky faucet can be annoying, but do not try to fix this problem yourself unless you know what you are doing. Do not create an even bigger problem. If you need assistance, do not hesitate to call Jim Dandy. Our trained and licensed professionals can fix your leaky faucets in no time. They can fix it at a reasonable price as well. When it comes to compression faucets, the rubber washers often wear out; they must be replaced occasionally. Most leaking compression faucets need new seat washers. If you replace the washers and your faucet continues to leak, then you might have a pitted seat. Remove the stem and grind the valve seat with a valve-seat dresser. When it comes to ball type faucets, finding the cause of the leak can be difficult since it contains a lot of parts. Sometimes it is recommended to buy a whole new replacement kit and put in all new parts. Do not ignore your leaky faucet. If you need proof of how much water a leaky faucet can waste, simply place a bucket underneath the faucet in question and leave it overnight. This can show you how much water is wasted.

Leaky faucet

Fix your leaky faucet to help prevent higher bills.

2. Water Pressure

Low water pressure may be indicative of something as simple as sediment buildup in a shower head, or as serious as a problem with the water lines that feed your water supply. The water delivered to your home should be between 35 and 80 psi (pounds per square inch). However, your local water utility typically uses regulators that deliver water between 50 and 70 psi, but a problem within your plumbing system could cause this pressure to change once it reaches your home. To check the water pressure in your home yourself, you can purchase a residential water pressure gauge kit. Once you get a water pressure gauge kit, you should select a water outlet that is close to your home’s main water supply source. Make sure that you turn off anything that uses water inside your home, including appliances and faucets. When using a gauge to test water pressure, you are testing the static water pressure. You could get a false low reading if there is any water that is moving in your plumbing system. Attach the gauge to the water outlet. Open the water supply valve that controls the outlet that the gauge is attached to. Make sure that you slowly open the valve until it is fully open. When the needle in the gauge stops moving, read the pressure. If it is below 50 psi or higher than 75 psi, your pressure reducing valve may be faulty or you may not have one installed on your water supply lines. It is recommended that you do at least a couple tests to make sure each reading is somewhat similar to one another. If you have a reading that is too high or too low, you should contact a professional plumber.

3. Leaks in Piping

A leaky faucet is one thing, but leaky piping is something completely different altogether. This is generally a much more complex repair work. If you notice wet spots on your walls, ceilings, or floors, then it may be that you need to repair and/or replace your piping before you incur serious water damage. Also, be on the lookout for mildew, which could be indicative of standing water (and a leak). The vast majority of leaks occur at or near plumbing fixtures like tubs, sinks, and toilets. If you know that it is a leak in your piping, you should call a plumber as soon as possible to get the issue taken care of to prevent further damage or increased bills.

4. Corrosion

Corrosion can be a big problem, and it has the potential to be detrimental to your water system. It can cause lasting damage on your water system, but it can also have harmful effects on the environment. If your pipes are corroded, you might possibly have to replace all the pipes in your system. To check for corrosion, you can test your water for copper. An abnormal level of copper can cause corrosion in your pipes. You can also check for rust because rust is a common by-product of corrosion. The easiest way to check for this is through your toilet tank. You can also inspect the exterior of your pipes and see if there are any pinhole leaks. If there are any leaks, you can know that it’s caused by corrosion if there are rusty, bluish, white or salt-looking sediments or stains around the leaks. Calling a local plumber to help could be a good idea.

corroded pipe

If you need help when it comes to your plumbing system – whether it deals with leaky faucets, water pressure, leaks in your piping, corrosion, or more – do not hesitate to call Jim Dandy. Do not allow a smaller issue to become an even bigger issue that could potentially cost you a lot of money. To schedule an appointment call 206-966-4548 or 425-454-8153.

By | 2017-07-28T08:23:03+00:00 July 10th, 2017|Plumbing and Sewer Tips for Keeping Your Home Safe and Dry|